歡迎來到Linux教程網
Linux教程網
Linux教程網
Linux教程網
Linux教程網 >> Linux基礎 >> Linux教程 >> ethtool 命令詳解

ethtool 命令詳解

日期:2017/2/28 14:01:04   编辑:Linux教程

命令描述:

ethtool 是用於查詢及設置網卡參數的命令。

使用概要:
ethtool ethx //查詢ethx網口基本設置,其中 x 是對應網卡的編號,如eth0、eth1等等
ethtool –h //顯示ethtool的命令幫助(help)
ethtool –i ethX //查詢ethX網口的相關信息
ethtool –d ethX //查詢ethX網口注冊性信息
ethtool –r ethX //重置ethX網口到自適應模式
ethtool –S ethX //查詢ethX網口收發包統計
ethtool –s ethX [speed 10|100|1000] [duplex half|full] [autoneg on|off] //設置網口速率10/100/1000M、設置網口半/全雙工、設置網口是否自協商

使用舉例:
1)[root@linux /]# ethtool eth1
Settings for eth1:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: umbg
Wake-on: d
Link detected: yes
2)[root@linux /]# ethtool -i eth1
driver: e1000
version: 5.0.43-k1
firmware-version: N/A
bus-info: 06:08.1
3)[root@linux /]# ethtool -S eth1
NIC statistics:
rx_packets: 58068300
tx_packets: 87124083
rx_bytes: 1589713008
tx_bytes: 2165825901
rx_errors: 0
tx_errors: 0
rx_dropped: 0
tx_dropped: 0
multicast: 0
collisions: 0
rx_length_errors: 0
rx_over_errors: 0
rx_crc_errors: 0
rx_frame_errors: 0
rx_fifo_errors: 0
rx_missed_errors: 0
tx_aborted_errors: 0
tx_carrier_errors: 0
tx_fifo_errors: 0
tx_heartbeat_errors: 0
tx_window_errors: 0
4)[root@linux /]# ethtool -s eth1 http://www.linuxidc.com/ autoneg off speed 100 duplex full

相關參考:
1)[root@linux /]# which ethtool //查詢 ethtool 存放的路徑
/sbin/ethtool
2)[root@linux /]# rpm -qf /sbin/ethtool //查詢 ethtool 的版本信息
ethtool-1.6-5
3)將 ethtool 設置永久保存在網絡設備的方法
解決方法一:
ethtool 設置可通過 /etc/sysconfig/network-scripts/ifcfg-ethX 文件保存,從而在設備下次啟動時激活選項。
例如:ethtool -s eth0 speed 100 duplex full autoneg off
此指令將eth0設備設置為全雙工自適應,速度為100Mbs。若要eth0啟動時設置這些參數, 修改文件/etc/sysconfig/network-scripts/ifcfg-eth0 ,添加如下一行:
ETHTOOL_OPTS="speed 100 duplex full autoneg off"
解決方法二:
將ethtool設置寫入/etc/rc.d/rc.local之中。

Copyright © Linux教程網 All Rights Reserved