平台：ok6410、Ubuntu、u-boot-2010.03.tar.bz2 ok6410 (128M RAM)
交叉編譯器：4.3.2
一、建立自己的開發項目並測試編譯
目前u-boot對很多cpu直接支持，比如smdk2400、smdk2410、smdk6400，但是沒有smdk6410，由於smdk6400與smdk6410硬件資源相近，所以我們選擇smdk6400為參照，建立自己的開發項目。
1、下載源碼、解壓
從 http://www.linuxidc.com/Linux/2011-07/38897.htm 下載 u-boot-2010.03.tar.bz2，之所以選擇此版本，是因為此版本與三星提供的u-boot.1.1.6相近，降低移植的難度。
2、進入board/samsun目錄下，會發現有smdk6400文件夾，建立新文件夾smdk6410，並將smdk6400裡的所有文件復制到smdk6410中，進入smdk6410文件夾將smdk6400.c更名為smdk6410.c，並且打開此文件，將裡面的6400全部改為6410。打開Makfile，將裡面的6400改為6410。結束推出到 u-boot-2010.03根目錄。
3、進入到nand_spl/board/sansung/，復制smdk6400，並黏貼，將副本smdk6400更名為smdk6410，更改Makefile文件，將裡面的6400全部改成6410。
4、進入到 include/configs/ 復制smdk6400.h，並將副本改為smdk6410.h。
5、進入到 u-boot-2010.03根目錄，打開Makefile，將CROSS_COMPILE ?=改成為CROSS_COMPILE ?=arm-linux-，然後搜索6400，會跳轉到如下圖所示
然後復制所有以上代碼，並且將6400改成6410，如下圖
然後運行make smdk6410_config 然後在運行make，若通過則說明此次移植第一步基本成功，但是編譯出來的u-boot.bin尚不能用，還要繼續深入工作。
二、修改啟動代碼
1、首先修改cpu/arm1176/start.s,修改後的代碼如下，
.globl _start
_start: b reset
#ifndef CONFIG_NAND_SPL
ldr pc, _undefined_instruction
ldr pc, _software_interrupt
ldr pc, _prefetch_abort
ldr pc, _data_abort
ldr pc, _not_used
ldr pc, _irq
ldr pc, _fiq
_undefined_instruction:
.word undefined_instruction
_software_interrupt:
.word software_interrupt
_prefetch_abort:
.word prefetch_abort
_data_abort:
.word data_abort
_not_used:
.word not_used
_irq:
.word irq
_fiq:
.word fiq
_pad:
.word 0x12345678 /* now 16*4=64 */
#else
. = _start + 64
#endif
.global _end_vect
_end_vect:
.balignl 16,0xdeadbeef
/*
*************************************************************************
*
* Startup Code (reset vector)
*
* do important init only if we don't start from memory!
* setup Memory and board specific bits prior to relocation.
* relocate armboot to ram
* setup stack
*
*************************************************************************
*/
_TEXT_BASE:
.word TEXT_BASE
/*
* Below variable is very important because we use MMU in U-Boot.
* Without it, we cannot run code correctly before MMU is ON.
* by scsuh.
*/
_TEXT_PHY_BASE:
.word CONFIG_SYS_PHY_UBOOT_BASE
.globl _armboot_start
_armboot_start:
.word _start
/*
* These are defined in the board-specific linker script.
*/
.globl _bss_start
_bss_start:
.word __bss_start
.globl _bss_end
_bss_end:
.word _end
/*
* the actual reset code
*/
reset:
/*
* set the cpu to SVC32 mode
*/
mrs r0, cpsr
bic r0, r0, #0x1f
orr r0, r0, #0xd3
msr cpsr, r0
/*
*************************************************************************
*
* CPU_init_critical registers
*
* setup important registers
* setup memory timing
*
*************************************************************************
*/
/*
* we do sys-critical inits only at reboot,
* not when booting from ram!
*/
cpu_init_crit:
/*
* When booting from NAND - it has definitely been a reset, so, no need
* to flush caches and disable the MMU
*/
/*
* flush v4 I/D caches
*/
mov r0, #0
mcr p15, 0, r0, c7, c7, 0 /* flush v3/v4 cache */
mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */
/*
* disable MMU stuff and caches
*/
mrc p15, 0, r0, c1, c0, 0
bic r0, r0, #0x00002300 @ clear bits 13, 9:8 (--V- --RS)
bic r0, r0, #0x00000087 @ clear bits 7, 2:0 (B--- -CAM)
orr r0, r0, #0x00000002 @ set bit 2 (A) Align
orr r0, r0, #0x00001000 @ set bit 12 (I) I-Cache
mcr p15, 0, r0, c1, c0, 0
/* Peri port setup */
ldr r0, =0x70000000
orr r0, r0, #0x13
mcr p15,0,r0,c15,c2,4 @ 256M (0x70000000 - 0x7fffffff)
/*
* Go setup Memory and board specific bits prior to relocation.
*/
bl lowlevel_init /* go setup pll,mux,memory */
/* when we already run in ram, we don't need to relocate U-Boot.
* and actually, memory controller must be configured before U-Boot
* is running in ram.
*/
ldr r0, =0xff000fff
bic r1, pc, r0 /* r0 <- current base addr of code */
ldr r2, _TEXT_BASE /* r1 <- original base addr in ram */
bic r2, r2, r0 /* r0 <- current base addr of code */
cmp r1, r2 /* compare r0, r1 */
beq after_copy /* r0 == r1 then skip flash copy */
#ifdef CONFIG_BOOT_NAND
mov r0, #0x1000
bl copy_from_nand
#endif
after_copy:
#ifdef CONFIG_ENABLE_MMU
enable_mmu:
/* enable domain access */
ldr r5, =0x0000ffff
mcr p15, 0, r5, c3, c0, 0 /* load domain access register */
/* Set the TTB register */
ldr r0, _mmu_table_base
ldr r1, =CONFIG_SYS_PHY_UBOOT_BASE
ldr r2, =0xfff00000
bic r0, r0, r2
orr r1, r0, r1
mcr p15, 0, r1, c2, c0, 0
/* Enable the MMU */
mmu_on:
mrc p15, 0, r0, c1, c0, 0
orr r0, r0, #1 /* Set CR_M to enable MMU */
mcr p15, 0, r0, c1, c0, 0
nop
nop
nop
nop
#endif
skip_hw_init:
/* Set up the stack */
stack_setup:
#ifdef CONFIG_MEMORY_UPPER_CODE
ldr sp, =(CONFIG_SYS_UBOOT_BASE + CONFIG_SYS_UBOOT_SIZE - 0xc)
#else
ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
sub r0, r0, #CONFIG_SYS_GBL_DATA_SIZE/* bdinfo */
#ifdef CONFIG_USE_IRQ
sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
#endif
sub sp, r0, #12 /* leave 3 words for abort-stack */
#endif
clear_bss:
ldr r0, _bss_start /* find start of bss segment */
ldr r1, _bss_end /* stop here */
mov r2, #0 /* clear */
clbss_l:
str r2, [r0] /* clear loop... */
add r0, r0, #4
cmp r0, r1
ble clbss_l
ldr pc, _start_armboot
_start_armboot:
.word start_armboot
#ifdef CONFIG_ENABLE_MMU
_mmu_table_base:
.word mmu_table
#endif
/*
* copy U-Boot to SDRAM and jump to ram (from NAND or OneNAND)
* r0: size to be compared
* Load 1'st 2blocks to RAM because U-boot's size is larger than 1block(128k) size
*/
.globl copy_from_nand
copy_from_nand:
mov r10, lr /* save return address */
mov r9, r0
/* get ready to call C functions */
ldr sp, _TEXT_PHY_BASE /* setup temp stack pointer */
sub sp, sp, #12
mov fp, #0 /* no previous frame, so fp=0 */
mov r9, #0x1000
bl copy_uboot_to_ram //此函數需要添加，稍後說明。
3: tst r0, #0x0
bne copy_failed
ldr r0, =0x0c000000
ldr r1, _TEXT_PHY_BASE
1: ldr r3, [r0], #4
ldr r4, [r1], #4
teq r3, r4
bne compare_failed /* not matched */
subs r9, r9, #4
bne 1b
4: mov lr, r10 /* all is OK */
mov pc, lr
copy_failed:
nop /* copy from nand failed */
b copy_failed
compare_failed:
nop /* compare failed */
b compare_failed
/*
* we assume that cache operation is done before. (eg. cleanup_before_linux())
* actually, we don't need to do anything about cache if not use d-cache in
* U-Boot. So, in this function we clean only MMU. by scsuh
*
* void theLastJump(void *kernel, int arch_num, uint boot_params);
*/
#ifdef CONFIG_ENABLE_MMU
.globl theLastJump
theLastJump:
mov r9, r0
ldr r3, =0xfff00000
ldr r4, _TEXT_PHY_BASE
adr r5, phy_last_jump
bic r5, r5, r3
orr r5, r5, r4
mov pc, r5
phy_last_jump:
/*
* disable MMU stuff
*/
mrc p15, 0, r0, c1, c0, 0
bic r0, r0, #0x00002300 /* clear bits 13, 9:8 (--V- --RS) */
bic r0, r0, #0x00000087 /* clear bits 7, 2:0 (B--- -CAM) */
orr r0, r0, #0x00000002 /* set bit 2 (A) Align */
orr r0, r0, #0x00001000 /* set bit 12 (I) I-Cache */
mcr p15, 0, r0, c1, c0, 0
mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */
mov r0, #0
mov pc, r9
#endif
/*
*************************************************************************
*
* Interrupt handling
*
*************************************************************************
*/
@
@ IRQ stack frame.
@
#define S_FRAME_SIZE 72
#define S_OLD_R0 68
#define S_PSR 64
#define S_PC 60
#define S_LR 56
#define S_SP 52
#define S_IP 48
#define S_FP 44
#define S_R10 40
#define S_R9 36
#define S_R8 32
#define S_R7 28
#define S_R6 24
#define S_R5 20
#define S_R4 16
#define S_R3 12
#define S_R2 8
#define S_R1 4
#define S_R0 0
#define MODE_SVC 0x13
#define I_BIT 0x80
/*
* use bad_save_user_regs for abort/prefetch/undef/swi ...
*/
.macro bad_save_user_regs
/* carve out a frame on current user stack */
sub sp, sp, #S_FRAME_SIZE
/* Save user registers (now in svc mode) r0-r12 */
stmia sp, {r0 - r12}
ldr r2, _armboot_start
sub r2, r2, #(CONFIG_SYS_MALLOC_LEN)
/* set base 2 words into abort stack */
sub r2, r2, #(CONFIG_SYS_GBL_DATA_SIZE+8)
/* get values for "aborted" pc and cpsr (into parm regs) */
ldmia r2, {r2 - r3}
/* grab pointer to old stack */
add r0, sp, #S_FRAME_SIZE
add r5, sp, #S_SP
mov r1, lr
/* save sp_SVC, lr_SVC, pc, cpsr */
stmia r5, {r0 - r3}
/* save current stack into r0 (param register) */
mov r0, sp @ save current stack into r0 (param register)
.endm
.macro irq_save_user_regs
sub sp, sp, #S_FRAME_SIZE
stmia sp, {r0 - r12} @ Calling r0-r12
add r8, sp, #S_PC @ !!!! R8 NEEDS to be saved !!!! a reserved stack spot would be good.
stmdb r8, {sp, lr}^ @ Calling SP, LR
str lr, [r8, #0] @ Save calling PC
mrs r6, spsr
str r6, [r8, #4] @ Save CPSR
str r0, [r8, #8] @ Save OLD_R0
mov r0, sp
.endm
.macro irq_restore_user_regs
ldmia sp, {r0 - lr}^ @ Calling r0 - lr
mov r0, r0
ldr lr, [sp, #S_PC] @ Get PC
add sp, sp, #S_FRAME_SIZE
subs pc, lr, #4 @ return & move spsr_svc into cpsr
.endm
.macro get_bad_stack
/* setup our mode stack (enter in banked mode) */
ldr r13, _armboot_start
/* move past malloc pool */
sub r13, r13, #(CONFIG_SYS_MALLOC_LEN)
/* move to reserved a couple spots for abort stack */
sub r13, r13, #(CONFIG_SYS_GBL_DATA_SIZE + 8)
/* save caller lr in position 0 of saved stack */
str lr, [r13]
/* get the spsr */
mrs lr, spsr
/* save spsr in position 1 of saved stack */
str lr, [r13, #4]
/* prepare SVC-Mode */
mov r13, #MODE_SVC
@ msr spsr_c, r13
/* switch modes, make sure moves will execute */
msr spsr, r13
/* capture return pc */
mov lr, pc
/* jump to next instruction & switch modes. */
movs pc, lr
.endm
.macro get_bad_stack_swi
/* space on current stack for scratch reg. */
sub r13, r13, #4
/* save R0's value. */
str r0, [r13]
/* get data regions start */
ldr r0, _armboot_start
/* move past malloc pool */
sub r0, r0, #(CONFIG_SYS_MALLOC_LEN)
/* move past gbl and a couple spots for abort stack */
sub r0, r0, #(CONFIG_SYS_GBL_DATA_SIZE + 8)
/* save caller lr in position 0 of saved stack */
str lr, [r0]
/* get the spsr */
mrs r0, spsr
/* save spsr in position 1 of saved stack */
str lr, [r0, #4]
/* restore r0 */
ldr r0, [r13]
/* pop stack entry */
add r13, r13, #4
.endm
/*
* exception handlers
*/
.align 5
undefined_instruction:
get_bad_stack
bad_save_user_regs
bl do_undefined_instruction
.align 5
software_interrupt:
get_bad_stack_swi
bad_save_user_regs
bl do_software_interrupt
.align 5
prefetch_abort:
get_bad_stack
bad_save_user_regs
bl do_prefetch_abort
.align 5
data_abort:
get_bad_stack
bad_save_user_regs
bl do_data_abort
.align 5
not_used:
get_bad_stack
bad_save_user_regs
bl do_not_used
#ifdef CONFIG_USE_IRQ
.align 5
irq:
get_irq_stack
irq_save_user_regs
bl do_irq
irq_restore_user_regs
.align 5
fiq:
get_fiq_stack
/* someone ought to write a more effiction fiq_save_user_regs */
irq_save_user_regs
bl do_fiq
irq_restore_user_regs
#else
.align 5
irq:
get_bad_stack
bad_save_user_regs
bl do_irq
.align 5
fiq:
get_bad_stack
bad_save_user_regs
bl do_fiq
#endif /* CONFIG_NAND_SPL */
